全国服务热线:

18396804865 钱经理

数控切割机切割板才品质优劣

2020-04-30 14:11:16 文章来源:www.jnzrtcsk.com 403

便携式数控切割机激光切割板才出去的品质优劣有各个方面缘故,其关键缘故有以下内容1、板才放置不稳定.必需时能够把板才加垫.

The quality of laser cutting board of portable NC cutting machine is good or bad because of various reasons. The key reasons are as follows: 1. The board is not stable until it is placed. It can be padded only when necessary.

2、割缝余量预留不足.尤其切割厚板时割缝余量至少在10mm以上.

2. The slot allowance is insufficient. Especially when cutting thick plates, the slot allowance is at least 10 mm.

3、工作环境光线不足.视觉观察不准确.尤其是阴天、晚上作业.

3. Insufficient light in the working environment, inaccurate visual observation, especially overcast and evening work.

4、切割中熄弧或未割穿,此时对与厚板一定重新移至切割点以上2MM处再继续切割,若未移至准确位置即起弧可能会对零件边缘进一步融割出现缺陷.

4. Extinguishing arc or not cutting in cutting. At this time, the thick plate must be moved to 2MM above the cutting point to continue cutting. If not moved to the exact position, arcing may cause defects in further cutting the edge of the part.

5、切割行进方向应确保切割结束在大面积板区.若结束在小面积板区会因受热板材移动导致切割变形.为此在切割厚板时可以正反方向各切割一段,相交处要及时熄火,避免切割过度致使零件缺损.

5. Cutting direction should ensure that the end of cutting is in large area. If the end is in small area, the cutting deformation will be caused by the movement of heated plate. For this reason, when cutting thick plate, the cutting section can be cut in both positive and negative directions, and the intersection should be extinguished in time to avoid excessive cutting resulting in part defects.

6、喷嘴,电极,喷嘴帽坚持每天检查,如有损坏及时更换.

6. Inspect nozzles, electrodes and nozzle caps every day and replace them in time if they are damaged.

7、划线要准确,留足割缝余量和板材边缘余量.

7. Marking should be accurate, leaving enough slot allowance and plate edge allowance.

8、厚板切割需加工的余量放到10MM-15MM.

8. The allowance for thick plate cutting should be placed at 10MM-15MM.

9、划线切割时板材摆放方向要结合零件排布、-X轴向切割来确定,力求便于观察.

9. The orientation of plate placement should be determined by combining the layout of parts and - X axial cutting, so as to facilitate observation.

10、造成切割尺寸误差的因素:对角线不准确、切割面倾斜、零件受热移动、一处多次重复起弧、划线不准确、起点、零点观察不准确等.

10. The factors causing the error of cutting dimension are inaccurate diagonal line, inclined cutting surface, parts moving by heat, repeated arcing in one place, inaccurate marking, inaccurate starting point, inaccurate zero observation, etc.

正确使用操作数控切割机能有效提高切割质量以及减少板材的浪费

Correct use of CNC cutting machine can effectively improve cutting quality and reduce waste of sheet metal http://www.jnzrtcsk.com/

  报错


  济南卓然天成是大型数控火焰切割机厂家,数控等离子切割机厂家,便携式数控切割机厂家www.jnzrtcsk.com,供应河北数控火焰切割机,山西数控等离子切割机,辽宁便携式数控切割机,吉林数控火焰切割机,黑龙江数控等离子切割机,江苏数控切割机,浙江数控切割机,安徽数控切割机,福建切割机,江西切割机,山东数控切割机,台湾切割机,河南切割机,湖北数控切割机,湖南数控切割机,广东切割机,海南数控切割机,四川数控切割机,贵州数控切割机,云南切割机,陕西切割机,甘肃数控切割机,青海数控切割机,需要的朋友联系我们15254176866

电话咨询
邮件咨询
在线地图
QQ客服
网站地图