全国服务热线:

18396804865 钱经理

数控等离子切割机改造升级服务

2019-10-14 16:59:09 文章来源:www.jnzrtcsk.com 323

大家一起了解新一代的数控等离子切割机改造升级服务:

Let's learn about the upgrade service of the new generation CNC plasma cutting machine.

一.遵照当地的电气规程来拟订电缆线的尺寸和类型.经常检查电缆线的外层是否有损坏(裸线危险),当电源线损坏时不要使用设备,如果电源线损坏应立即更换.

1. Draw up the size and type of cable in accordance with local electrical regulations. Check the outer layer of cable regularly for damage (bare line danger). Do not use equipment when the power line is damaged. If the power line is damaged, replace it immediately.

二.如果等离子电源装置的盖子未装好,不要使用等离子系统,裸露的电源端子有很大的危险性.

2. If the cover of the plasma power supply device is not installed, do not use the plasma system. The exposed power supply terminals are very dangerous.

三.当切割下料时不要去拾工件及废料.

3. Don't pick up the workpiece and scrap when cutting.

四.更换任何电气部件之前,应先断开供电电源,等待5分钟让电容放电后再进行操作.

4. Before replacing any electrical components, the power supply should be disconnected and the capacitor should be discharged for 5 minutes before operation.

五.设备必须可靠接地,机床体、控制箱及等离子电6.保持你的身体及衣服的干燥.当使用设备时不要站在、坐在或躺在潮湿的表面.

5. Equipment must be grounded reliably. Machine body, control box and plasma electricity 6. Keep your body and clothes dry. Do not stand, sit or lie on wet surfaces when using equipment.

六.提供相应的绝缘材料以防电击,如果你必须工作在靠近潮湿的区域要特别当心,戴上绝缘手套,穿上绝缘鞋.

6. Provide appropriate insulation materials to prevent electric shocks. If you have to work near damp areas, take special care. Wear insulating gloves and insulating shoes.

七.提供一个装在墙上的带有相应保险的空气开关接至设备,该开关使得操作者在遇到紧急情况时可快速切断电源.

7. Provide a wall-mounted air switch with corresponding safety to the device, which enables the operator to switch off power quickly in case of emergency. http://www.jnzrtcsk.com


  济南卓然天成是大型数控火焰切割机厂家,数控等离子切割机厂家,便携式数控切割机厂家www.jnzrtcsk.com,供应河北数控火焰切割机,山西数控等离子切割机,辽宁便携式数控切割机,吉林数控火焰切割机,黑龙江数控等离子切割机,江苏数控切割机,浙江数控切割机,安徽数控切割机,福建切割机,江西切割机,山东数控切割机,台湾切割机,河南切割机,湖北数控切割机,湖南数控切割机,广东切割机,海南数控切割机,四川数控切割机,贵州数控切割机,云南切割机,陕西切割机,甘肃数控切割机,青海数控切割机,需要的朋友联系我们15254176866

电话咨询
邮件咨询
在线地图
QQ客服
网站地图